1. Start up (a) Before the connection of the pump, determine whether the rotation direction of the motor is correct and whether the rotation of the pump is flexible (or check the motor rotation after the pump is filled with water, and it is forbidden not to run dry in the pump) (b) Close the discharge tube Gate valve on the road. (c) Fill the pump with water or use a vacuum pump. (d) Turn on the power, when the pump reaches normal speed, and then gradually open the discharge valve on the pipeline, and adjust to the required conditions. In the discharge tube gate valve closed case, the pump can not work more than 3 minutes. 2, stop (a) gradually close the discharge valve on the pipeline, cut off the power. (b) If the ambient temperature is below 0 ℃, the pump water should be released to prevent cracking. (c) If it is to be stopped for a long time, the pump should be disassembled, cleaned and oiled, and should be stored in a package. 3, operation (a) During driving and running, we must observe the instrument readings, bearing temperature, fill leakage and temperature rise and pump vibration and noise is normal, if abnormal circumstances should be promptly addressed. (b) The difference between the bearing temperature and the ambient temperature does not exceed 40 ° C, and the maximum bearing temperature does not exceed 80 ° C. (c) Filler water leakage should be small and uniform. (d) Bearing oil level should be maintained in the normal position, can not be too high or too low, low oil should be replenished promptly. (e) Replace the new seal ring if the gap between the seal ring and the impeller is too worn. (The diameter of the new pump should be about 0.15 ~ 0.25mm) (f) The pump should be operated at the performance point (flow rate, Lift, etc.) near the operation, so that the pump can work in high efficiency long-term, in order to achieve the maximum energy-saving effect. 1. Start up (a) Before the connection of the pump, determine whether the rotation direction of the motor is correct and whether the rotation of the pump is flexible (or check the motor rotation after the pump is filled with water, and it is forbidden not to run dry in the pump) (b) Close the discharge tube Gate valve on the road. (c) Fill the pump with water or use a vacuum pump. (d) Turn on the power, when the pump reaches normal speed, and then gradually open the discharge valve on the pipeline, and adjust to the required conditions. In the discharge tube gate valve closed case, the pump can not work more than 3 minutes. 2, stop (a) gradually close the discharge valve on the pipeline, cut off the power. (b) If the ambient temperature is below 0 ℃, the pump water should be released to prevent cracking. (c) If it is to be stopped for a long time, the pump should be disassembled, cleaned and oiled, and should be stored in a package. 3, operation (a) During driving and running, we must observe the instrument readings, bearing temperature, fill leakage and temperature rise and pump vibration and noise is normal, if abnormal circumstances should be promptly addressed. (b) The difference between the bearing temperature and the ambient temperature does not exceed 40 ° C, and the maximum bearing temperature does not exceed 80 ° C. (c) Filler water leakage should be small and uniform. (d) Bearing oil level should be maintained in the normal position, can not be too high or too low, low oil should be replenished promptly. (e) Replace the new seal ring if the gap between the seal ring and the impeller is too worn. (The diameter of the new pump should be about 0.15 ~ 0.25mm) (f) The pump should be operated at the performance point (flow rate, Lift, etc.) near the operation, so that the pump can work in high efficiency long-term, in order to achieve the maximum energy-saving effect.
The five Channels Controller can seperatly control UV IR Warm White Cold White and Red spectrum in LED Grow Light. This allows for light throughout the plant's growth from VEG to Bloom. MixLux Master Controller supports LED Grow Lights, HPS Grow lights, HID Grow light and CMH Grow Light dimming. We guaranty 3 years warranty, from the date of receipt of goods, if the product is damaged due to quality problems. MixLux will compensate for new products and find out the quality problems and make improvements. The Lighting Controller with six menus : LED dimming, light cycle, light type, temperature protect, sunrise and sunset config----- configure system time and display the operation log.
Five Channels Controller,Spectrum Adjust Controller,Optimal Spectrum Grow Light Controller,Bar Grow Lights Dimming Controller
Shenzhen MixLux Technology Co., Ltd , https://www.mixluxled.com