1, in addition to comply with this note strictly GB3883.1-83 "hand-held power tools safety management, inspection, maintenance of technical regulations," the relevant provisions. 2, the product within the voltage range of ± 10% before use. 3, to avoid the electrical level and water, oil in the installation of electric place, all of this pump, do not damage the power level, and to avoid oil, water and electrical switches and other electrical parts of the contact. 4, to prevent a sudden start, the power switch is turned on before the "off" (that is, press into) state. 5, do not abuse the power cord, the power cord may not be any length or exchange. Can not pull the power cord scraping, cutting and rolling bad phenomenon. 6, the pump flameproof type, when replacing the brush or repair, pay special attention to the explosion-proof surface of explosion-proof parts can not damage the hair. When repairing or replacing the brush, please turn on the motor to clean the inner cavity toner and oil rot. 7, Proper use of hand, the pump power cord without a plug at the end, the user selects the right plug, with two sides and three knives point special attention: A, as in the explosive and flammable with plugs and sockets must comply with the explosion-proof procedures plug With the socket, set in the normal field away from explosive and flammable venues, available 220V5A three-pin plug, one of the long legs for the ground. B, no matter what kind of plug should be reliably grounded, the power cord at one end of the yellow-green wire for the ground wire, when properly connected, should check the pump metal case and the contact between the legs are electrically connected, which is resistance should not be greater than 1 European mother. 8, the banned place: In special environments such as wet, snow and corrosive gases can not be used. Instructions for use: 1, the provisions of the use of voltage: line voltage does not exceed the pumping pump nameplate voltage ± 10% before use. 2, How to equip: After unpacking, assemble according to the sketch of the structure, connect the motor (1) and connect the mobile phone (2) with the pump body and the motor as a whole (3) Parts in good condition to boot. 4, the pump should not be empty running, use, the suction is completed, that is, stop the pump, otherwise it will speed up impeller seals bearing wear and tear. May also wear pump tube, the pump motor idling speed of up to 10000 rev / min. 5, timely exchange of brushes, brush wear will not be able to use, must be promptly replaced (2 brush at the same time exchange) Otherwise it will brush and commutator bad contact caused by ring loss, damage commutator, severe punishment will be Burned armature. 6, in the following circumstances shall not be used in the course of such as the discovery of insulation damage, the power cord cable jacket rupture, plug or socket cracking or poor contact, and intermittent operation, severe punishment sparks and other failures, the motor shell operation, Should be repaired immediately. Do not use before repair. 7, to prevent overload, when used, where the speed anomaly or reduced, it should stop to check whether there are debris stuck impeller or motor failure, electric pump for some reason must immediately cut off the power when the brake. 8, to use the tools to cherish, all pumping pump to be careful to avoid being hit. Maintenance 1, often fat, electric pump for high-speed operation, easy to volatile grease, it must be maintained at the bearing lubrication, and pay attention to Tim. 2, regular inspection and maintenance, electric pump should always check, repair, to check the power cord: the internal wiring, plugs, switches are good, the insulation resistance is normal, the tailstock is loose, the commutator and the brush in good contact , Armature-level expansion of the stator winding is a proper way to break the phenomenon of bearing and rotating parts are damaged and so on. 3, save each part and exchange the same parts, the pump in the demolition of the pump, you should save each part, pay special attention to explosion-proof parts explosion-proof surface can not make damage to the hairline, including insulation pads and casing, If damaged, it must be replaced with the same new parts, shall not be used below the performance of alternative raw materials or parts of the original specifications do not match, all parts should be assembled according to the original location, can not be omitted. 4, pay attention to insulation resistance, long-term shelved or used in wet environments electric pump, before use must use 500-volt megger to measure the winding insulation resistance. If the insulation resistance between the winding and the motor housing is less than 7 megohms, the winding must be dried. 5, pay attention to save, electric pump should be placed in a dry, clean and non-corrosive gas environment.
Waterfall Sink
Waterfall sinks, also known as trough sinks or cascade sinks, are an increasingly popular type of KITCHEN HANDMADE SINK that offer a sleek and modern look. These sinks feature a flat surface sloping downward into a basin, and water flows over the surface into the basin, resembling a waterfall.Waterfall sinks come in a variety of shapes and sizes, ranging from rectangular to oval, and are made from a variety of materials, including glass, stone, and ceramic. They also come in a range of styles, from minimalist and contemporary to more ornate and decorative designs.One of the benefits of a waterfall sink is that it can be easier to clean than other types of sinks, as there are no edges or crevices for dirt and grime to accumulate. Additionally, the waterfall effect can be visually striking and adds a unique touch to any bathroom.When choosing a waterfall sink, it`s important to consider the size and style of your bathroom, as well as your personal preferences and budget. With so many options available, there is sure to be a waterfall sink that meets your needs and complements your bathroom décor.
Waterfall Sink, SUS304 Stainless Stain Waterfall Sink, Pvd Nano Waterfall Sink
JIANGMEN MEIAO KITCHEN AND BATH CO.,LTD , https://www.meiaogroups.com