Floor drain is one of the indispensable sanitary hardware supplies for every family. The volume is small and the use is really big! It is an important connection between the drainage pipe system and the indoor floor. It plays an important role in preventing odor, preventing clogging, and preventing flooding. The quality of the floor drain directly affects the air quality and sanitary environment of the bathroom space. However, no matter how good the floor drain is, if it is used for a long time, it needs to be replaced. Then what should be done to replace the floor drain? Today we will learn about floor drain replacement .
Floor drain replacement steps
Floor drain replacement step 1 : before changing the floor drain must be optimistic about the current use of the old floor drain panel and the size of the specification model, the general home with the most 10*10cm square majority, but does not rule out some houses with a round 12CM model; As for the size of the sewage pipes, the diameter of common residential dwelling pipes is 50 pipes, that is, the diameter is 50mm. The floor drains of general manufacturers meet this requirement and this will not be considered. The panel size of the new floor drain should be consistent with the size of the old floor drain.
Floor drain replacement step 2 : The old floor drain and the tile joint can be separated by using a screwdriver or other tools to slowly open and separate.
Floor drain replacement Step 3: Be sure to remove the odor-resistant core before installing the four core floor drains . If you do not directly install the deodorant core, it may cause impurities such as cement sand to enter the core, affecting the results.
Floor drain replacement Step 4 : Align the panel with the four core floor drains and the tiles. Note that the height cannot be higher than the tiles. Apply glass glue or white cement around and dry.
Floor drain daily maintenance tips
Floor drains are usually not eye-catching, but they are bad but even if they are replaced with new floor drains, we must pay attention to the daily maintenance of floor drains.
Maintenance method: regular cleaning floor drain
Floor drains need to be cleaned regularly. When cleaning floor drains, it is usually necessary to clean the debris on the cover first to prevent debris from entering the sewers and causing fouling. Then remove the cover plate and brush the parts of the floor drain with a brush, which can be supplemented with some cleaning agents. Then sterilize and deodorize the sewer and reinstall the floor drain. Daily care should not be taken to drain the floor drain of the floor drain, and food residue should not be poured directly into the floor drain.
Maintenance method II: water seal floor drain needs regular water injection
If the installation is a water seal floor drain, during use, care should be taken to prevent the water seal from drying up and regular water injection is required. If you do not use it for a long period of time, it is better to seal the floor drain with a lid to reduce the evaporation of water, but also play a role in sealing.
Maintenance Method 3: Self-closing leaks should be checked regularly
Self-sealing floor drains do not require water seal floor drains, and their seals are often sealed by mechanical devices such as springs and magnets. The spring, for example, tends to decrease in elasticity as the use time increases, and the magnet weakens due to the absorption of iron in the water. Therefore, it is necessary to regularly check whether the performance of the self-sealing floor drain is good. If problems occur, they need to be replaced in time.
Editor's summary: On how to replace the floor drain , Xiao Bian will roughly introduce it to it. The home is leaking, and you no longer need to find a maintenance master. You can change it yourself! If there are other questions, we can also leave a message and we will answer your questions as soon as possible! More decoration information, all on this site, so stay tuned.
Floor drain replacement
Product name Zinc Phosphate
CAS No 7779-90-0
EC No 231-944-3
Chemical formula Zn3(PO4)2.2H2O
Appearance White Powder
Storage Keep the product in a tightly closed container ,Isolate form any source of heat or ignition and moisture
Packing unit 25kg Poly Propylene bag & 500kg Poly Propylene bag,
Any size customers want.
Application Material for anti-corrosion paint used in container,
Ship and steel structures .Electronic materials
Goods characteristics White Powder.
Soluble in acid or alkali solution ,insoluble in water or alcohol.
CHEMICAL ANALYSIS
★ Product grade: Zn 50.5-52%
|
TEST ITEM |
UNIT |
REQUIREMENT |
|
Whiteness |
% |
80-90 |
|
Zn |
wt.% |
50.5-52 |
|
PO4 |
wt.% |
20-30 |
|
Moisture |
wt.% |
Max1.0 |
|
Oil absorption |
ml/100g |
25-35 |
|
The PH Value |
- |
6-8 |
|
Residue on sieve (325mesh) |
wt.% |
Max0.5 |
|
Mean Particle Size |
μm |
44 |
50.5% Zinc Content Zinc Phosphate
50.5% Zinc Phosphate, Anticorrosive Paint 50.5% Zinc Phosphate
shijiazhuang city xinsheng chemical co.,ltd , https://www.xsphos.com