The waterproof treatment that should be done in home decoration is mainly in the kitchen and bathroom. When the built home is delivered for use, leakage does not occur. However, in the home decoration, the sanitary facilities and the upper and lower water lines are often moved, which will cause the original waterproof layer to be damaged. In this case, we must re-waterproof. The following areas are required for waterproofing:
>>> Links: Hydro-Renovation and Decoration Cheats
1. Resurfaced floors: When the kitchen floor is renovated, the waterproof layer is most likely to be destroyed. During the renovation, it is necessary to protect the original waterproof layer as far as possible. Once it is damaged, it must be repaired in time to re-do the waterproof layer. When the floor tiles are replaced, after the original floor tiles are cut away, the ground shall be smoothed with a cement mortar and repeatedly painted with a polyurethane waterproof coating for 2 to 3 times. Pay attention to uniform brushing so as to avoid excessive thinness and leakage.
2. The wall adjacent to the bathing facilities: Wash basin. When the sink is in use, water will splash on the adjacent wall. If there is no waterproof layer, the wall will be easily wet and mildew will occur. Therefore, before the wall tiles are laid, it is necessary to do a good job of waterproofing the walls, but the non-load-bearing lightweight walls should be at least 1.8 meters high. It is best to make the entire wall waterproof. The waterproof surface of the wall adjacent to the shower position should also be 1.8 meters high. The height of the waterproof paint on the wall adjacent to the bathtub should also be higher than the upper edge of the bathtub.
3. Joints between wall and floor, upper and lower water pipes and the ground: Leakage mostly occurs in the pipe roots, floor drains, sanitary ware, and yin and yang corners that pass through the floor, due to the looseness and adhesion of pipe roots, floor drains, etc. Insufficient, incomplete brushing or partial damage to the waterproof layer, and insufficient length of the component overlap. These corners are the most prone to leaks. Attention should be paid to the construction of detailed nodes in weak areas. The waterproof coating must be applied in place. When pipelines, floor drains, etc. cross the floor, the waterproof layer around the holes must be carefully constructed. The upper and lower water pipes shall be well cemented and sturdy, and a 10-20 cm polyurethane waterproof coating shall be brushed upward from the ground, and then a polyurethane waterproof layer shall be made on the ground, and the original waterproof layer shall be used to form a composite waterproof layer to enhance the waterproof performance.
4. Walls of buried water pipes: Buried pipes in the wall should be made of grooves larger than the diameter of the pipes. The grooves should be smooth and smooth, and then the grooves should be brushed with a polyurethane waterproof coating for waterproof treatment.
5. Sewage outlets and floor drains: The floor of the kitchen and kitchen must be drained to the ground in order to make the drainage smooth and free of stagnant water. During the renovation, the original drainage and sewer pipes and floor drain locations should be avoided. `~
Hydroelectric renovation paint home decoration cement house bathroom waterproof bathroom tile bathroom floor tile kitchen tile
High speed shutter door is a rapid operating, anti-crash shutter door for indoor application . The most advantage of this door is that the opening/closing speed can reach to 0.6-1.8m/s, really fast action a lot than tranditional rollling shutter door. short opening and closing times reduce cooling loss, avoid airflow and enable a smooth operating procedure. They can also be designed in larger dimensions for the mining and aircraft industries.
High speed door can be easily installed, economical,quiet and efficient with electromechanical drive.
This door quickly though in/out open gate, ideal for warehouses,factories, hangars use, widths can be from 2m to 20 meters.
The material of this door are variety: PVC curtain to keep the insdie clean, heavy duty aluminum door with wind-resisitant function can wrok in heavy windy weather, and also the freezer door can be used in cold warehouse or somewhere like that.
Including models are:PVC High Speed Door, Aluminum Spiral High Speed Door, Self-Recovery repair door, Cold Storage Room Fast Door.
High Speed Door,PVC High Speed Door,Aluminum High Speed Door,Spiral High Speed Door
Shenzhen Hongfa Automatic Door Co., Ltd. , https://www.hfhighspeeddoor.com