<br> <br> 1 Scope This regulation sets out the relevant provisions of the vibrating pile driver safe operation.
This procedure is applicable to the company's vibration sinking pile machine operation.
2 main content
2.1 The operator must be professionally trained to understand the construction, principle, operation and maintenance of the pile driver being operated. And hold the operation permit before you can operate.
2.2 The power unit, winch, hydraulic device, electrical equipment, etc. configured for the pile driver shall be operated in accordance with its operating procedures. Enterprise Management Base Camp Forum
2.3 The electrical failure of the pile driver must be handled by an electrician.
2.4 The commissioning, installation, disassembly, haulage, etc. of the pile driver shall strictly follow the provisions of the instruction manual.
2.5 In case of thunderstorms such as thunder, rain, snow, fog and winds above the sixth level, the operation should be stopped. When the wind speed exceeds seven or there is a strong typhoon warning, the pile machine should be parked in the wind direction and the pile tube should be sunk into the soil. Below 3 meters or put the vibrating hammer on the ground and add a windproof cable. If necessary, the rack should be lowered. The pile driver must take lightning protection measures. When lightning strikes, personnel must be away from the pile driver. Enterprise Management Base Camp Forum
2.6 First run before each shift, and wait until the status of each component is normal before working. Enterprise Management Base Camp Forum
2.7 If the pile is used, the pile should be clamped before work, and the pile should not be loosened during operation. When the job is stopped. The vibration of the vibratory hammer must be stopped first, then the gripper is released. Business management
2.8 When installing the vibrating hammer, the vibrating hammer must be transported within 2 mm directly in front of the pile frame.
2.9 When the pile driver walks, turns, and has a special position, it must be directed.
2.10 The pile brake should be slow and the continuous running in the same direction should be less than one week.
2.11 Hanging vibration hammer, hanging material, hanging pile, walking and turning, etc. It is strictly forbidden to carry out two or more actions at the same time.
2.12 Lifts are strictly prohibited from being overloaded.
2.13 The operator cannot leave the post without authorization.
2.14 The following conditions should be immediately stopped for maintenance:
2.14.1 Parts are removed from the column and the diagonal support; enterprise management
2.14.2 Vibratory hammer The motor fastening bolt is loose, the guiding device is loose, there is impact sound in the exciter, the bearing temperature rise is too high, and the connecting bolt of the vibrating hammer and the pile or other device is loose.
2.14.3. Electrical equipment and hydraulic equipment have failed. Enterprise Management Base Camp Forum
2.15 If the vibration beam vibration beam amplitude is too large for a long time, stop the machine to find out the cause.
2.16 When the pile is piled, the verticality of the pile should be corrected in time. After the pile has entered the soil for 3m, it is strictly forbidden to use the pile machine to walk or turn to correct the verticality of the pile.
2.17 The pile frame column that cannot be tilted left and right should be adjusted. When adjusting the column, the left and right diagonal braces should be driven at the same time.
2.18 When the operation is stopped every day, the pile pipe should be submerged below the soil, or the vibrating hammer should be placed on the ground, and the power of the pile driver should be cut off to make all the braking work. When the machine is stopped for a long time, the pile machine should be parked on a solid and flat ground. Above, the vibratory hammer must be dropped and padded and protected against rain.
2.19 When the pile frame is raised and lowered, the hoist drum should be checked for reliability and then lifted and lowered according to the procedure specified in the instruction manual.
2.20 Walking type, when the track pile driver is not working, it should be parked in the middle of the shoe or track, and the rail clamp must be clamped.
2.21 When disassembling the oil pipe, ensure that the pipe joint is not contaminated.
- Bluetooth wireless
- Built-in speaker
- Built-in microphone
- Handsfree speakerphone
- Supports profile A2DP (Advanced Audio Distribution Profile)
- Aux in (3.5mm audio input)
- Micro-USB port for battery recharge
- Wireless range: 10 meter
- Controls: volume up, volume down, play/pause, pairing/answer phone
- On/off switch
- LED pairing indicator
- DC battery power: built-in rechargeable battery
- Battery life: ~5 hours at 100% volume
- Dimensions:Diameter 115mm*Height 145mm
- Includes: Micro-USB cable, Aux plug,
Bluetooth Speaker,Portable Bluetooth Speaker,Mini Bluetooth Speaker,bluetooth Wireless Speaker,portable wireless speaker
Shenzhen Lanejoy Technology Co.,LTD , https://www.grill-mesh.com