Door and window process knowledge

First, door and window cover production:
1. The woodworking master hits the standing board and solid wood lines with an impact hammer to fix the eye. The wooden wedge is allowed to dry in the sun for one day. After the anticorrosive treatment, the nail is inserted into the already opened eye. When the cover is set, the wood is brushed against the wall and the tung oil is made again. Moisture treatment
2. Put a high-quality joinery board against the wall and brush the tung oil and then screw it into the wall. Use a level ruler and a wire camel to hold it horizontally, vertically, and squarely. The board is filled as tightly as possible. The edge of the blockboard station is sufficient to withstand the weight of the door leaf and the nail holding force of the hinge, and the door stop is made with a nine-percent board to make the dark side mouth, and the small wooden line head;
3, the door line with nine PCT board bottom, the side with solid wood small lines sealed, solid wood door lines and other solid wood lines should be purchased 4-5 days in advance, do not open the bundle on the site to dry, and the surrounding air integration, Nail windows and doors must be artificially set aside more than 1 mm of contraction, must not immediately close. Normally (Summer) shrinks more than 3 days, (Winter) shrinks more than 6 days and then closes again;
4, kitchen, bathroom door line and ground to set aside 1 cm spacing, so as not to pull the ground;
5. It is forbidden to use wood for windowsills. It is recommended to use natural stone, artificial stone, tiles, mosaics, etc.;
6. The production of window cover wood should be made after the natural stone or artificial stone is installed, so as to achieve a tight seam;
7. Wood products that need to be mixed with oil should be treated with “V” grooves in the line and contact of solid wood.

Second, the door page production:

1. Flat door production: use two high-quality blockboards to form solid doors, and open the board to the corresponding slots with a depth of 3mm and a spacing of 12cm. Use woodworking glue to open the corresponding slots. The wood boards were laminated together, and the panels were decorated on both sides. The weight was more than 500 pounds on a flat surface for more than 10 days. During the pressing process, the front and back sides were flipped 3-4 times. After 10 days, the door blank was closed with solid wood lines. Solid wood lines must not be closed immediately after closing. Usually shrink in summer more than 3 days, winter contraction more than 6 days and then close the mouth;
2, bump process door production: the middle with a high quality blockboard open the corresponding slot, both sides of 9-12 PCT clip system, on both sides of the decorative panel, on the flat surface of 500 kg or more weight to suppress more than 10 days, suppression During the process, the front and back sides were flipped 3-4 times. After 10 days, the door blank was closed with solid wood lines. (Dry-shrinking process as above);
3, wardrobe door production process: the middle with 12-15 PCT board, 15 PCT must open the corresponding slot, on both sides of the decorative panel, where to reach the length of 140 cm above the door to be placed in the door on both sides of a stainless steel bar, put On the flat ground, more than 500 kilograms of weight is pressed for more than 10 days. During the pressing process, the front and back sides are flipped 3-4 times. After 10 days, the door blank is closed with solid wood lines. (Dry-shrinking process as above) The door width should not exceed 45 cm;
4, sliding door production process: work and other leaves almost the same, the track should be hidden in the door cover, both sides of the glass to use custom-made solid wood small clips, the ground positioner to be solid, the location should be reasonable.

Doors & Windows Tiles Windowpanes Glass Doors Stainless steel Decorative glass tiles Kitchen sliding doors Glass doors Glass doors Kitchen doors Glass sliding doors Glass doors Kitchen doors Glass sliding doors Bathroom sliding doors Bathroom tiles Bathroom doors Tile adhesives Kitchen tiles

Tin Copper Lead Free Soldering Bar

Tin Copper Lead Free Soldering Bar,Casting Solder Bar Copper,Soldering Material Casting Bar,Tin Lead Soldering Material Casting Bar

NINGBO XIHAN TIN SOLDER CO.,LTD. , https://www.soldertop.com