Zanhuang Police Tip: Traveling in Snow and Ice is a little common sense

The Zanhuang Police warmly reminded that safety is the key to travel in icy and snowy weather. I hope that all drivers and friends should pay attention to safety at all times when driving, and do the following ten points.

1. Pay attention to the driving distance. A certain driving distance should be maintained with the vehicle in front. Especially in snowy days, the sight is relatively poor, and the driving speed should be slow and uniform to avoid sharp turns and sharp braking.

2. Pay attention to observe and judge the pavement, especially in the case of turns, ramps, turnouts, upper and lower bridges, etc. covered by ice and snow, do not pass blindly.

3. Drive smoothly while driving, do not go back and forth in parallel, try to avoid overtaking, try to be decisive when changing lanes, turn on the turn signal in advance, reduce the number of brakes, especially to avoid emergency braking.

4. Turn slowly when turning, do not violently turn, use hand brake when parking, use point brake to slow down when using foot brake, do not step on one foot, stop slowly.

5. If there is a rut on the snowy road, you should follow the rut. If the rut is frozen and shallow, it should be driven by the rut. Snow control is referred to as "slowly lifting the clutch and slowly supplying oil, shifting and reducing the temperature and throttle.

6. Give full consideration to others, especially anticipate emergency situations such as cyclists and pedestrians may suddenly fall due to slippery roads. Therefore, when driving through intersections and pedestrian crossings, keep a safe distance from pedestrians and non-motorized vehicles, and avoid rushing.

7. In foggy days, especially at night and early morning when the fog falls, and the sight distance is short, measures such as turning on fog lights, whistle whistle, long distance, and deceleration should be taken.

8. Maintain a good line of sight. Make sure that the windshield, rearview mirror and reversing mirror are clean and clear. When passing through intersections and T-junctions, do not be obstructed by trucks, buses, and other vehicles.

9. Due to snowfall, especially after rain and snow, the temperature is low. From night to early morning, a thin layer of ice easily forms on the road surface, and the wheels are very easy to slip after rolling. In this regard, drivers, especially new drivers, should be very careful when driving vehicles.

10. Vehicles driving in snow should be flushed in time after the snow stops. More and more corrosive impurities in the snow melt agent will cause damage to the paint surface, chassis, tires, etc. Therefore, the vehicle should be cleaned in time.

In addition, due to the low temperature in the car in winter, when people enter the car, a lot of breath will form on the front windshield, affecting the driver's front line of sight. Solving this problem can generally be solved in the following two ways:

1. Use automatic air conditioner to defog operation, that is, turn on the automatic air conditioner and set the mode switch to the defog gear. At this time, the air conditioner will automatically switch to external circulation, and the outside air will enter the cab, and the defog will begin.

2. If it is a manual air conditioner, you should first adjust the wind direction switch to the defogging gear, start the external circulation to let fresh air blow in, and adjust the compressor and wind speed to the highest to speed up the defogging speed. If you feel that the defrosting of the side glass is not fast enough, it is best to close the two central air outlets so that the airflow from the air outlets on both sides quickly blows off the mist. You can also open the window appropriately to speed up the demisting.

Abrasive Fiber Disc

The abrasive fiber disc specifications, size and grit are more, please contact the customer before taking the picture, and the confirmation shall prevail!

Features: This abrasive polishing fiber disc is also called fiber disc, grinding disc, high-speed grinding disc, etc.

An organic coated abrasive made of abrasive and high-strength rigid paper as the base material and bonded by synthetic resin.

Product features: The abrasive fiber disc is a sheet-shaped abrasive tool made of steel paper as the matrix, and the synthetic resin is used to consolidate the abrasive on the matrix.

Scope of application: Abrasive fiber disc can be used for rough processing of various complex surfaces made of metal materials, such as paint removal, rust removal, burr removal, and welding seam grinding. It is widely used in shipbuilding, aviation, locomotives, bridges and other industries.

It is mainly installed on electric: dynamic or pneumatic angle grinders to remove rust, deburr, paint, and polish welds on metal and various non-metallic materials, as well as grinding, smoothing, and polishing in mechanical repair work. , An ideal tool for scraping, and it is also widely used in corner polishing and carving in the furniture industry.


The related abrasive products we can supply is Flap Disc Adhesive , Abrasive Flap Disc , Abrasive Sanding Disc, Bonded Abrasives , and Abrasive Machine such as Flap Disc Making Machine, Abrasive Belt Making Machine, Flap Wheel Machine , Sanding Disc Machine, if you have any needs about abrasive tools, please kindly feel free to contact us.

Abrasive Fiber Disc 3Abrasive Fiber Disc 7Abrasive Fiber Disc 6

Abrasive Fiber Disc,115 fiber disc,Zirconia Fiber Disc,Silicon Carbide Fiber Disc,Abrasive Fiber Disk For Metal

Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.abrasive-jd.com