For many homeowners, the decoration of new houses is indeed a very troublesome thing, especially the decoration of the wall is a very important process in the renovation, because this is the basic of interior decoration. Even if some owners live in the room for a long time, they will find bubbles, mildew, water seepage and other phenomena on the wall. This may be because the wall was not ready during the renovation. Next, Xiaobian introduced the decoration wall treatment process for everyone, hoping to help the decoration owners.
1. Interface agent: The brush interface agent must be brushed and brushed.
2, cracks: Under normal circumstances with kraft paper tape and white latex cracks
3, leveling: uneven wall needs leveling, the general gypsum is more commonly used, concave and convex difference does not exceed 0.5 centimeters.
4, patch: general light walls and insulation walls and other non-load-bearing walls are required to be patched, try to choose a little better texture of the wall cloth and white latex, if conditions can be used grid cloth, the relative anti-crack effect will be Better.
5, putty: The use of high fineness and texture harder putty is better, you can also add some white latex in the putty, you can improve the hardness of putty.
6, polished: as far as possible with a fine sandpaper, generally soft texture of the putty (such as 821) with 400-500 sandpaper, hard texture (such as wall lining, Yi Yiping) with 360-400 better, If the sandpaper is too thick, it will leave a deep sand mark and the paint cannot be covered. After polishing, you must thoroughly clean the wall to avoid too much dust, affecting the paint adhesion. The unevenness does not exceed 3 mm.
7. Primer: The primer must be evenly brushed to ensure that the wall is brushed in every place. If the wall has a large amount of paint to eat, it is best to add a little amount of water to the primer to ensure even brushing. Do not think it is because it is the primer to use a little more than a roller on it, the primer brushing effect will directly affect the effect of the top coat, use the same texture as the paint roller.
8, find repair: Putty after polishing is completed, there will be some blemishes (pit eyes), under normal circumstances it is difficult to see, only after the paint will be obvious once again, this time you need to find fill, pay attention to make up must be polished smooth , And then use a little more to add a little water to the primer brush again, so as not to brush when the paint because of the different amount of water with the other wall and a color.
9, topcoat: Do not add too much water, will affect the film thickness, feel and hardness of the paint, try to choose a little better tool, the drum's hair should not be too short, but it must be fine, so that the brush out of the paint film Will feel delicate, brushing mainly pay attention to the corner, each part of the roll and the direction of paint recovery, corner treatment, most of the time is the use of brush or brush to brush, this will easily cause the edge of the texture and the entire surface is inconsistent, visually There will be differences, if you have conditions, you can buy a side roller, the corner brush with a board and then use the side roller to receive it again, pay attention to the material of the side roller and brush the same side of the roller, brush the big side Every time the paint is connected, it must be evenly distributed. It must not be too thick or too thin. Otherwise, it will cause inconsistent light reflection due to uneven thickness. When you paint, it will have a paint-removing action. The direction of each paint roll must be the same, otherwise it will cause the texture of each roll to roll out of the inconsistent, reflective angle will be different, there will be visual differences. (Recommendation: buy a tray before painting, the shop will have to sell, use the tray to ensure that each brushing a roll, the paint on the roller is the same, so that the brush is very uniform.)
10. Maintenance: 4 hours after the latex paint is applied, it will be dry, but the dried paint film has not reached a certain hardness. This requires care. It is very simple. Do not scrub or touch the wall within 7-10 days. Face action can be.
Editor's summary: The process of decorating the wall is introduced here. For more information, you can follow this site information.
Living room decoration
ZHEJIANG HESHUO TECHNOLOGY CO.,LTD , https://www.hosuocn.com