Stone Decoration Scheme I. Material Requirements
1, stone according to design requirements, determine the variety of stone color, pattern and size specifications, and strict control, check its strength, water absorption and other properties.
2. The quality of the expansion bolts, connecting iron pieces, connecting stainless steel pins, and other iron pads, washers, nuts, and brackets required for various designs and installations must meet the requirements.
Second, the main machine bench drill, toothless cutting saws, impact drills, pistol drills, tape measure, by feet and so on.
Third, the operating conditions
1, check the quality of the stone and whether the performance of all parties meet the design requirements.
2. Take a stand and do a hidden inspection.
3, hydropower equipment and other retainers have been installed.
4, doors and windows have been completed.
5. Make technical disclosures to the participants.
Fourth, the operating process
1. Process flow → cleaning the surface of the structure → popping the vertical line on the structure → hanging the two vertical wires at the big corner
→ Stone drilling -→ Back side brushing -→ Adhesive reinforcement material
Hang the horizontal position line → support the bottom board bracket → place the bottom board positioning → adjust and temporarily fix → fill M20 cement → set the drain pipe → structure drilling and insert the fixing bolt → insert the stainless steel fastener →
Fill the hole in the lower wall plate with adhesive → Insert the connecting steel pin → Fill the adhesive into the lower hole of the upper wall plate to temporarily fix the upper wall plate → Drill the hole to insert the expansion bolt → Insert the stainless steel fastener → Inlay the top wall plate →
2. Receipt of construction site: The responsible person will find quality problems, deal with it in time, and be responsible for stone stacking at the site.
3, stone preparation: The use of colorimetric method to select the color of the stone classification, installed in the same side of the stone should be the same color, according to the design drawings and block order stone number.
4. Grassroots Preparation: Clean up the surface of prefabricated stone facings. At the same time, structure and rules will be set. Vertical lines and horizontal lines will be popped up. According to the design drawings and actual needs, pop up the position line and block line of the installation stone.
5. Hanging line: According to the requirements of the design drawings, before the stone is installed, the theodolite shall be used to combat the vertical control lines of the two sides of the big angle in advance. It is better to play the position of 20cm from the big angle so that the exact line of the vertical thread can be inspected at any time to ensure Install smoothly and mark up and down the control line.
6, a branch of the bottom veneer bracket, the pre-arranged support according to the flat line supported on the bottom of the floor to be installed above the stone. The support should be firm and be connected to each other, and it can also be connected with the shelves. After the support is in place, the 50mm thick wood planks should be passed through the nails in the supporting direction. The planks should be on the same level. Ensure that the stone is on the same level below.
7, on the connection of iron: stainless steel bolts with the design provisions of angle steel and steel plate. Adjust the position of the flat steel plate so that the small hole of the flat steel plate just faces the insertion hole of the stone plate, fix the flat steel plate, and tighten with a wrench.
8, the bottom of the stone installation: the side of the iron connection is good, we can put the bottom panel on the corner of a piece in place.
9, adjust the fixed: After the panel temporarily fixed, adjust the level, such as the surface of the board is not flat, can be in the bottom of the bottom of the plate connected to the flat steel pad on the corresponding double-copper wire mat. Adjust the verticality and adjust the distance from the wall of the stainless steel connector on the panel to the wall gap until the panel is vertical.
10, the top panel installation: In addition to the top floor of the top panel to understand the general stone installation requirements, the installation adjustment is good, in the structure and the gap in the stone hanging a long 20mm thick wooden bar, wooden bar flat for the stone plate down 250mm, The hanging point can be set on the connecting iron. After the wooden strips are lifted, the fillers can be put in the gap between the slab and the wall, and the packing is tight to prevent the slurry from leaking during grouting.
11. Clean up the marble and granite surfaces: Remove the antifouling strips on the marble and granite surfaces.
Wipe the slate with cotton.
V. Finished product protection:
1. It is necessary to clean it in time, and the net remains in the stains on the door and window frame, glass and metal, and the decorative panel.
2. Conscientiously implement a reasonable construction sequence, and a few types of work should be done in the front to prevent damage and contamination of the external stone decorative panels.
3. When disassembling shelves and loading materials, it is forbidden to collide dry hanging stone decorative panels.
4. When the exterior finishes are finished, the corners of the easily damaged part are to be protected by nails, and other types of work must not be scratched or damaged.
5. The completed external stone shall be guarded by special persons. In the event of endangering the finished product, it shall be immediately stopped and severely dealt with.
Six, should pay attention to the quality of the problem
1. The surface color of the exterior stone slabs is different. The main reason is that the quality of the stone is poor. There is no trial spelling and careful selection during construction.
2. The lines are not straight, the seams are not uniform, and they are not straight. The actual size of the construction of the structure is not checked before the construction, and the actual size of the construction is checked. The segmentation is divided into blocks. The line is not thin, the cable is not straight and the line is not calibrated. Diligence and other reasons.
3, plastic caulking is not fine, the operator should be serious construction, inspection personnel should be carefully accepted.
4. The wall surface is dirty and strabismus has glue marks. The first is the operation process. The second is the operation staff. It is necessary to strengthen the protection of the finished product and carefully clean up before completion.
Buy Materials Stainless Steel Window Marble Glass Painted Aluminum Door Glass Glass Door
Beauty instrument accessories refer to various components that are used in the development and production of beauty devices. These accessories include parts and attachments that aid in the proper functioning of beauty instruments including facial massagers, hair removal devices, and skin rejuvenation equipment.
Beauty instrument accessories are precisely manufactured to exacting standards to ensure that they meet the required specifications. These accessories are used in a wide range of beauty devices from simple handheld devices to sophisticated equipment used in beauty salons.
One of the significant advantages of beauty instrument accessories is their versatility. With a wide range of attachments and parts available, these accessories are designed to cater to the needs of different beauty instruments. They can be designed to suit different skin types, skin treatments, and different target areas to offer a complete cosmetic toolset.
Beauty instrument accessories are made from high-quality materials that are safe for use on the skin. The materials used in these accessories are hypo-allergic and are designed not to cause any irritation. This is especially important when developing and producing beauty devices that come into direct contact with skin regularly.
These accessories also offer efficient and rapid results when used appropriately with the right beauty instrument. With the precision manufacturing of these accessories, there is an assurance of high efficiency, leading to a noticeable change in the skin after treatment.
In conclusion, beauty instrument accessories are a critical component in the beauty industry. They help improve the efficacy of beauty devices and offer versatile solutions for different skin types and requirements. With their high-quality materials, safety, and efficacy, beauty instrument accessories remain an essential tool for beauty treatment around the world.
Beauty Instrument Parts,Beauty Apparatus Accessories ,Beauty Apparatus Parts ,Custom Beauty Instrument Parts
Lizhi Precision Manufacturing Technology Co.,Ltd , https://www.autoindust.com