How to repair the wear parts of ZYB heavy oil coal tar pump? 1. Wear and maintenance of gears: The wear parts of the gears are mainly the meshing of the teeth, the involute working face and the planes at both ends of the gear. When it is slightly worn, the tooth surface can be polished with oil stone, and the two ends are flat and polished on the flat plate. How to repair the wear parts of ZYB heavy oil coal tar pump?
1, gear wear and maintenance:
The wear parts of the gears are mainly the meshing of the teeth, the involute working surface and the plane of the two ends of the gear. When it is slightly worn, the tooth surface can be polished with oil stone, and the two ends are flat and polished on the flat plate. When the tooth surface of the gear is seriously worn, the new gear should be replaced. If only the flat ends of the gear are worn, the surface can be ground and polished.
2, shaft wear and maintenance:
The wear of the shaft of the heavy oil pump is mainly due to the frictional wear between the two ends of the shaft and the supporting needle, which makes the shaft diameter smaller. If it is slightly worn, the diameter of the shaft can be increased by plating a layer of hard chrome to repair the shaft. If the shaft wears seriously, it should be re-manufactured with 45 steel or 40Cr steel. After the shaft blank is roughed and finished, the bearing part should be heat treated, the hardness is HRC60-65, and then ground, so that the surface roughness of the bearing mating part is not Ra. It is larger than 0.32 μm; the roundness and cylindricity tolerance of the shaft is 0.005 mm; the gear matching portion is H7/h6, and the surface roughness Ra is not more than 0.63 μm.
3. Wear and maintenance of the pump body:
The surface wear of the pump is mainly the arc-shaped working surface of the oil-absorbing section. If there is slight wear, it can be used after grinding and deburring with oil stone. The pump body is molded from cast iron, and new parts should be replaced when there is severe wear. If both ends of the pump internal gear are repaired by grinding, the width of the pump body should also be changed, which is equal to the size of the gears at both ends of the gear. The reworked end faces of the pump body should meet the technical requirements.
4, wear repair of the two ends of the cover:
The end cover of the heavy oil pump is made of cast iron. After the wear phenomenon occurs, it can be slightly polished and flattened on the flat plate. When the damage is serious, the surface should be ground and flattened on the surface grinder. The plane contact between the repaired end cap and the pump body should be no less than 85%. The flatness tolerance, the perpendicularity of the end face to the centerline of the hole, the parallelism tolerance of the end faces and the center of the two shaft holes The parallelism tolerance of the line is O.Olmm. The surface roughness Ra after grinding should be no more than 1.25 μm.
5. Repair and replacement of needle roller bearings for pumps:
After the parts in the pump are repaired, the bearing needles should be replaced. The requirements for needle roller are: the dimensional error of all needle roller diameter should not exceed 0.003mm, the length tolerance is 0.1mm, and the clearance with the shaft should be about O.Olmm; when the needle roller is assembled, it should be filled in the bearing shell according to the quantity requirement. The needle rollers should be arranged parallel to each other.
Http://news.chinawj.com.cn
Stainless steel wire is a versatile material that is used in a variety of applications due to its strength, corrosion resistance, and durability. It is ideal for use in WIRE MESH, wire rope, and other applications where high strength and corrosion resistance are required. Stainless steel wire is available in various grades and sizes, allowing it to be tailored to specific needs and requirements.
Anti-corrosion stainless steel wire is a type of stainless steel wire that has been specially treated to resist corrosion. This makes it ideal for use in harsh environments where corrosion is a concern, such as marine applications or chemical processing plants.
Stainless steel wire for wire mesh is a type of stainless steel wire that is specifically designed for use in wire mesh. This type of wire is often used in applications such as fencing, screens, and grates. It is also commonly used in the construction industry for reinforcement purposes.
Stainless steel wire rope is a type of wire that is made from stainless steel and woven into a rope-like structure. This type of wire is extremely strong and durable, making it ideal for use in heavy-duty applications such as lifting and towing. Stainless steel wire rope is also resistant to corrosion, making it suitable for use in marine and industrial environments.
Stainless Steel Wire,Anti-Corrosion Stainless Steel Wire,Stianless Stel Wire For Wire Mesh,Stainless Steel Wire Rope
Hebei Aibuer trading co., Ltd , https://www.ablehardwares.com