Cabinets are standard in every home kitchen. However, in the face of numerous cabinet brands, people cannot start; especially high prices make people hesitant. So, how does the kitchen cabinet save money? Which kind of kitchen cabinet material is better? Because of the high frequency of cabinet use, and the high requirements for applicability and durability, as well as the relatively large effort in home decoration, so before the renovation In the preparation work, cabinets often take a lot of effort to consider. If you're still bothered by how the kitchen cabinets are done , you might as well go down with me!
How to make kitchen cabinets
1. First, determine the orientation of sinks, gas stoves, and sockets according to the area of ​​the kitchen, the orientation of the launching water, and the use of customs, etc., and determine the distinction between each compartment of the cabinet. The simple way is to go to the neighbors' homes of the same apartment.
2, hydropower projects. Tell the master about the orientation of the sink and socket. At this time, you can wire and spread hot and cold water pipes.
3, the next is the mason. As the carpenter and the mason are playing at the same time. First and foremost, make a table with a height of 10cm, and play the role of waterproof and dampproof.
4, before the cabinet, the sink, gas stoves, hoods, etc. to get the hand, how to distinguish between cabinets, they can also figure it out. Wooden cabinets should pay attention to waterproof and moisture. Such as: sink or pull basket under a layer of waterproof paper.
What materials are good for kitchen cabinets
1, the kitchen environment is not good, more oily oil, it is not difficult to choose a useful kitchen cabinet, eco-board is a good choice.
2. Eco-board, with Malacca fine carpenter board or multi-layer board as the base board, covered with professionally made plates, with the features of no paint, environmental protection, wear-resistance and anti-corrosion, and easy cleaning.
3, eco-board can meet the use of cabinets, eco-board in terms of the appearance of texture, can be divided into three categories: 1. Mirror ecology board 2. Relief surface ecological board 3. Pock eco-board.
4, mirror ecological board, the appearance is very lubricated, lubricated as a mirror, is the choice of materials used; embossed ecological board, the appearance of a small relief sculpture; pock eco-board, looks similar suede photo, easy to clean.
Cabinets save money
1. The design size should be within the principle
Some owners will raise the floor cabinets or thicken the top cabinets, thinking that they can store more. In this regard, experts have introduced: Cabinets have industry common design principles. For example: cabinet manufacturers in the production and installation process, the size is fixed, hanging cabinet diameter 330mm deep, 600mm within the depth of the table, the ground is about 900MM from the table about the height of the table from the bottom of the cabinet 650~750MM Around, it is not recommended to change it.
2. Optional items can be freely selected
The stage basin will be changed to the lower basin, and the drawers will be dampened. These are all items that are not included in the standard and will increase the customization cost. Is it really necessary to choose?
Experts said: adding functional hardware to the cabinet brings comfort. For example: Drawer plus damping, less noise, safe to use. But no increase, it can be used normally. So it depends on the owner’s budget and usage habits.
3. Hardware table budget to do enough
Want to reduce the cabinet budget, do not use hardware and desk. Because these two are the most frequently used ones, good quality can be used for 10 years, and poor quality one or two years may require maintenance.
Countertops: High-quality quartz countertops, resistant to acids and alkalines, longer service life. Inferior artificial stone countertops, though inexpensive, may crack, deform, etc. in a short time.
Editor's summary: Creating a kitchen cabinet for the kitchen not only has a decorative effect but also makes cooking a treat. It is believed that you will have a good understanding of how kitchen cabinets are done when you finish reading the kitchen cabinets.
How to make cabinets
Our Tungsten Carbide Tipped Cutters(TCT hole saws) are a superior alternative to conventional Bi-Metal Hole saws. They cut faster, cleaner, and last longer. Say goodbye to burnt out, smoking holesaws. Try a T.C.T. you'll love it.
Tungsten cutters cut through, steel plate, iron, aluminium, copper, cast iron, and most importantly, stainless steel and other tough alloys.
The spring loaded pilot bit ejects the cut slug, saving time. The cutter body then cuts a clean, burr-free hole faster than conventional twist drills or hole saws.
T.C.T. cutters are the standard for electrical construction, transit work and general metal fabrication. The spring on the pilot bit ejects the cut slug.
With normal care, Tool life is significantly longer than other hole cutting tools. Inexpensive resharpening will allow repeated use
Tct Hole Saw,Tct Cutting Disc,Carbide Circular Saw Blade,Tct Hole Saw Cutter
Behappy Crafts (suzhou)Co.,Ltd , https://www.behappyindustry.com